– wiring (Denso) for Wingroad with Y12, Electrics. Frame / Series, Y12 / Y12, body, W (wagon), engine, HR15DE (HR15DE engine), drive, 2WD. HR15DE engine model. flexible wires and anchors, work properly. If loose parts, deterioration, cuts .. to any components or wiring of the supple- mental air . HR15DE engine torque curve. Achieves plentiful low-end torque extending through mid-to-high engine speed. MR20DE engine torque curve. liter engine.

Author: Meztikora Shakakree
Country: Bahrain
Language: English (Spanish)
Genre: Technology
Published (Last): 12 April 2018
Pages: 175
PDF File Size: 11.41 Mb
ePub File Size: 5.30 Mb
ISBN: 322-9-81719-762-4
Downloads: 60816
Price: Free* [*Free Regsitration Required]
Uploader: Mesar

Under the following conditions? P P Detected items Intake valve timing control Exhaust valve timing control Engine operating condition in fail safe mode The signal is not energized to the intake valve timing control solenoid valve and the valve control does not function.

Below 3, rpm after the following conditions are met. After warming up, idle the engine Accelerator pedal: More than 1 second after turning ignition switch Witing [Engine is running] [Ignition switch: OFF Air conditioner switch: The fail safe function also operates when above diagnoses except MI circuit are detected and demands the driver to repair the malfunction.

The following page uses this file: ECM stops the electric throttle control actuator control, throttle valve is maintained at a fixed opening approx. When electric throttle control actuator does not function properly due to the return spring malfunction: Therefore, acceleration will be poor.


Wiring for – Nissan TIIDA/TIIDA LATIO C11 | Japan sales region, ,

Below 3, rpm after the following conditions are met – Engine: You may do so in any reasonable manner, but not in any way that suggests the licensor endorses you or your use. Idle air volume learning has not been performed yet. A few seconds after turning ignition wirig OFF [Ignition switch: Idle air volume learning has already been performed successfully. After the vehicle stops, the engine stalls.

APEXi SMART Accel Controller Harness Adapter – A – RHDJapan

P er Bank 2 High Input: ECM controls the electric throttle control actuator by regulating the throttle opening to 20 degrees or less. Idle speed [Engine is running]? Fully depressed [Ignition switch: The ECM regulates the opening speed of the throttle valve to be slower than the normal condition.

P P P P Detected items Mass air flow sensor circuit Engine coolant temperature sensor circuit Engine operating condition in fail safe mode Engine speed will not rise more than 2, rpm due to the fuel cut.

For 1 second after turning ignition switch ON [Engine is running] [Ignition switch: Therefore, when electrical controlled throttle and part of ECM related diagnoses are continuously detected as NG for 5 trips, ECM warns the driver that engine control system malfunctions and MI circuit is open by means of operating hr1de safe function.


When disconnecting ECM harness connector Aloosen C it with levers as far as they will go as shown in wirihg figure.

File:Nissan HR15DE engine 001.JPG

Fully depressed Accelerator pedal: ON] [Engine is running]? Adjust ignition timing with a timing light before monitoring IGN TIMING, because the monitor may show the specification data in spite of the ignition timing not being adjusted to the specification data. Fully released Clutch pedal: The engine speed will not rise more than 2, rpm.

No load Idle 2, rpm Clutch pedal: Response ratio Lean to Rich Response rate: Specification data are reference values.

You may select the license of your choice. After warning up, idle the engine? ON Heater fan switch: This licensing tag was added to this file as part of the GFDL licensing update.

ECM is located in the engine room left side near battery. No load Not used. Not being turned Steering wheel: ON Selector lever rh15de